If you wish to own a 3D printer for your work or creativity you should definitely have a look on the printers mentioned below. There has been an increased demand, and therefore there has been a revolution in 3D printers since 2017. They have continuously gained popularity among the people as well as advancement in technology. So if you are passionate about 3D printing then these are the best suggested tools for you. CR 10 was launched in 2016 and it is still running the show pretty well. While, Ender 3 was brought into market space in March, 2018.
Ender 3 comes with a higher printing speed of 180 mm per second and is also cheaper, costs around 200 dollars, whereas CR 10 has a lower printing speed of 100 mm per second. While, CR 10 has a larger printing bed compared to Ender 3. This is the main difference.
The price was reasonable and the quality was dependable, therefore, it again gained importance. When you observe superficially there is a high probability that you might think they are similar, however, it is only when you dig in deeper that you get to know the differences in the features and a few specifications which will make all the difference for you to buy them. The tools vary from the size, to the speed, purchase price and in other features. So let us dig deeper and check for yourself which is the exact equipment you are aiming for. Below listed are the specifications that would take you through the journey of making you understand the details of these equipment.
Ender 3 vs CR 10 Specifications
|
Article |
Ender 3 |
CR 10 |
|
Print Area Measurements |
220 x 220 x 250 cm |
300 x 300 x 400 mm |
|
Nozzle Measurement |
0.4 mm |
0.4 mm |
|
Filament used |
1.75 mm PLA, ABS TPU |
1.75 mm PLA, ABS TPU |
|
Printing Speed (maximum) |
180 mm/s |
100 mm/s |
|
Affordability |
Around 200 dollars |
Around 350 dollars |
|
Heating Temperature |
110 degree Celcius |
80 degree Celcius |
|
Heating process |
Faster, 5 minutes |
Gradual, 20 minutes |
|
Input power |
120 to 220 volts |
120 to 220 volts |
|
Output power |
24 volts |
12 volts |
|
Assembling time |
60 to 120 minutes |
60 minutes |
Ender 3 Review
Impressive Add ons:
The equipment, Ender 3 is extremely impressive when it comes with the extra features that it has. One being the BuildTak print surface. The good thing about this print bed is that you can detach it and can connect several newer components. You just have to do it manually by turning the nuts and adjusting them again when you attach the component. This would be really helpful because you are not limited to just one thing, you can use it for other things as well. Further, there comes the power saving mode. This mode becomes really beneficial when there is no power and you still have to meet the deadline and take the prints. Well, now you can do it. It is promising that way so that your work does not hamper at any cost.
Assembling
The equipment is very easy to set up and satisfy your printing enthusiasm. The box comes with all the parts inside and it is semi- assembled in a way but by that you should not panic at any cost, wondering how to arrange the set. It is doable, certainly. It would take only around 60 minutes for you to get all set. All you need to do is pick up the instruction manual given in the box and start assembling. The way the box comes, half of the job is already done for you so as to give you the go- ahead.
Maintaining the Temperature
The machine is capable of maintaining an average temperature throughout the print bed so that there is no unequal heating of the surface for better results. Further, you must also know that the heating of the bed does not take much time. It is quick as well as reliable. Also, the temperature does not switch too often, it stays consistent when the printing time is long. The mechanism is such that it avoids any kind of power fluctuations. This allows the bed to be heated in a continuous manner at up to 110 degrees and that too in just a span of 5 minutes.
CR 10 Review
Heating process
The heating process is gradual and steady with this equipment. The machine can go up and record a temperature of 80 degree celsius. The time taken to heat the printing bed to the maximum temperature takes around 20 mins which is more compared to the previous model. The reason can be stated as the larger printing bed is involved in this machine. The printer is open and therefore it takes some time to heat the bed consistently so that there is no unequal heating taking place which might otherwise degrade the quality of the output produced.
Assembling
The assembling process for the CR 10 model is less time consuming compared to the Ender 3 model. Which takes 60 minutes to 120 minutes to get completely assembled . However, CR 10 just takes 30 minutes and another 30 minutes to level the bed. The CR-10 is a little larger in size compared to the previous model as the electrical box comes as a separate piece and not along with the frame which was not the case in Ender 3 as everything came together attached to the frame. However, you do not have to worry about assembling as the process is doable with the manual provided along with the box which helps you understand which part at which position and you can get started with your passion for printing.
Easy to use
The CR-10 3D printer is not all complex in terms of usage. You don’t need any expertise to start working on the printer for 3D printing. The machine is there for you to get started. It is one of the best budget printers available in the martkr. The printing bed can be handled manually. All you need to do is set the bed in the right position at the right level and tighten the nuts and get started with yyu work. The good thing is that the nust used are comparatively bigger and stronger which provides more stability to the printing bed. It gives you more control over the machine and can be handled without much effort.
Conclusion
All the features are listed to help you understand well what the products are entirely for and service do they bring along. You can make an intelligent choice based on that decision and see that the tool serves you the best. Ender 3 printers come at an affordable price and therefore do not meddle much with your budget. Also, it prints with a higher speed there it becomes a better choice when you have a job where a lot of documentation and printing is involved. CR 10 is one of the best 3D printers when it comes to the plate size it offers.
The printer bed is large enough and it would certainly prove to be a benefit when you need to take prints of huge 3D models. This is better even than various upgraded versions. You can view the features and also check how much you would be able to meddle with your budget. The idea is to provide you with the best tool that can go along and fulfil your requirements as to what your work or hobby demands. However, as far as the technical factor is concerned the tool is way ahead in that and completes the work with efficiency.
Watch the Video till End
FAQs (Must Read)
Q. If there is more printing work that needs to be done which of the above printers should be used?
A. In that case it is better to use Ender 3 as it has a better printing speed.
Q. Which of the 2 models saves electricity while working?
A: Ender 3 comes with a power saving mode which can be used even in the case of power failure.
Q: Does the printer have the option to resume printing later?
A: Yes, the printer has that option embedded in it.
Q: Is there any return policy associated with the printer?
A: Yes, the product can be returned within a period of 10 days.
Q: Which of the above tools is portable?
A: Ender 3 is lighter in weight and therefore can be carried easily from one place to another without any hassle.
Q: Is the machine durable?
A: Yes, the machine lasts long and it is strong as it uses aluminum as the material.
Q: Why does the temperature on the plate need to be consistent?
A: The printing bed needs to be heated in a way that the models created should be of the best quality which can be obtained via this.
Q: Which printer should be bought in case of tight budget?
A: Ender 3 is the correct choice in case you are not trying to meddle much with your budget.
Q: What is the time difference that is there to heat the printer beds completely?
A: About 15 minutes is the time difference to heat the two different printer beds.
Q: What is the voltage input and output in case of CR – 10 model?
A: The input can be anywhere between 110 – 220 Volts while the output is 12 Volts.